Currency
Welcome, Log in
The Xilinx Spartan-3A Evaluation Kit ...
low-cost JTAG configurati- on USB solution ...
All manufacturers altri - miscellaneous Arrow Electronics, Inc. Avnet Electronics Marketing Digilent, Inc. Genode Labs GbR GlobalTop Technology Inc. Hirose Connectors Infineon Technologies AG OHO-Elektronic Samtec, Inc. Sarantel Limited Telit Wireless Solutions Trenz Electronic GmbH TrioFlex OY Xexun Xilinx, Inc.
No specials at this time
-- price: lowest first price: highest first name: A to Z name: Z to A in-stock first sort by
Digilent 2-pin MTE cable connector (power)
Digilent 6-pin header connector and gender changer
Digilent 2x6-pin header connector and gender changer
For use with the XUP USB-JTAG Programming Cable (XUP-USB-JTAG)
Digilent 1-pin MTE cable connector
Digilent 2-pin MTE cable connector (9 inches)
Digilent 6-pin MTE cable connector
Digilent 2-pin MTE cable connector (18 inches)
The Digilent PmodCON4 peripheral module connects a 6-pin header to two RCA audio jacks allowing you to connect to audio equipment.
The PmodLED has four high-bright LEDs that are driven by logic-level transistors so each LED can be illuminated with a logic high signal that provides less than 1mA of current.
The PmodSSD offers a single two-digit seven-segment display device (7sd) that can attach directly to any Digilent system board.
The Digilent PmodBTN Pushbutton Module Board allows four momentary pushbuttons to be added to any system board using a 6-pin header connector.
The Digilent PmodSWITCH Switch Module Board has four slide switches that can be used to provide on and off inputs into a circuit or board.
The Digilent PmodTPH2 Test Point Header Module Board (the TPH2) is an ideal way to test the connection between a Pmod and system board with 12-pin (2x6) connectors loaded.
The Digilent PmodCON1Module Board is designed for use with a Digilent system board and conveys I/O signals between six screw terminals and a 6-pin header connection.
The Digilent PmodCON2 Module Board makes it easy to connect a Digilent system board to outside devices with BNC plugs.
The PmodRS232 Converter Module Board (the RS232 module) translates voltage from the logic levels used by Digilent system boards to the RS232 voltage used for serial communications.
The Digilent PmodOD1™ Open Drain Output Module Board can drive high current devices using On-Semiconductor NTHD4508NT power FET output transistors.
The PmodMIC is ideal for providing audio input for use with Digilent system boards. It has a microphone preamp with a dynamic range compressor and 12bit A/D converter.
The PmodLS1 module is an interface module for connecting optical sensors to digital inputs on a Digilent system board.
The Pmod Breadboard provides a ready made solution for prototyping breadboarded circuits using the Digilent 2x6 pin interface.
Serial Flash ROM 128 Mbit
FX2 Module Interface Board
Digilent FX2 Wirewrap
4 x 8-bit digital-to-analog output converter
The Digilent PmodTMP is ideal for users that need a thermometer or thermostat in a digital design.
The Digilent PmodDIN1 Digital Input Module Board (the DIN1™) debounces digital input signals so they can be used directly by a Digilent system board.
The Digilent PmodHB3 2A H-Bridge Module (the HB3) is an ideal solution for robotics and other applications where logic signals are used to drive small to medium-sized DC motors.
The PmodSD Secure Digital media card module provides a convenient SD card slot for use with Digilent system and microcontroller boards.
2 x 12-bit analog-to-digital input converter
The Digilent Pmod DA2 Digital to Analog peripheral module converts signals from digital values to analog voltages on two channels simultaneously with 12-bit resolution.
The Digilent PmodSF provides easily accessible non-volatile memory storage for Digilent FPGA and Microcontroller system boards.
The Digilent FX2 Breadboard (FX2BB) offers a ready-made solution for prototyping breadboarded circuits as accessories to Digilent system boards.
Two axis joystick.
The PmodCLS module can be used to display important debugging information during program development or as a user interface for completed designs.
The PmodCLP is a 16x2 character LCD module that uses two Pmod connectors to present a 3.3V, 8-bit parallel data interface to system boards.
SMSC EVB-USB3300-XLX USB Daughter Card
Low-cost JTAG configuration USB solution. Replacement for Digilent JTAG USB Cable (JTAG-USB).
The Digilent Cerebot™ 32MX4 Board is a powerful microcontroller development board suitable for embedded control and robotics projects for both students and hobbyists.
low-cost JTAG configuration USB solution compatible with Xilinx Platform Cable USB (HW-USB-G) for all Xilinx devices.
The Basys board provides an ideal circuit design platform for anyone who wants to learn about FPGAs and digital circuit design.
The Spartan-3 Starter Board provides a powerful, self-contained development platform for designs targeting the new Spartan-3 FPGA from Xilinx.
items: 10 20 50 50
No products
Shipping 16,00 € Total 486,66 €
Prices are tax included
Cart Check out
telegramma - chat with us
chiamaci - call us
All new products
All best sellers