Customers frequently viewed
Carrier Board for Trenz Electronic 4 x 5 Modules (TE0701-06)
This carrier board is only for the use of Trenz Electronic modules with a standard footprint of 4 x 5 cm.
Item number VAR-827003405
Manufacturer Product Number: TE0701-06
Taric/custom code: 84718000
Item located in and dispatched from: Riedlingen, Germany
The predecessor of this article is TE0701-05. All changes are in the Product Change Notification (PCN).
Important: Upcoming changes from TE0701-06 to TE0701-07.
The Trenz Electronic TE0701 Carrier Board is a base-board for 4 x 5 SoMs, which exposes the module's B2B-connector-pins to accessible connectors and provides a whole range of on-board components to test and evaluate TE 4 x 5 SoMs.
See page "4 x 5 cm carriers" to get information about the SoMs supported by the TE0701 carrier board.
Notice
Do not access the FT2232H EEPROM using FTDI programming tools, doing so will erase normally invisible user EEPROM content and invalidate stored AMD/Xilinx JTAG license. Without this license the on-board JTAG will not be accessible any more with any AMD/Xilinx tools. Software tools from FTDI website do not warn or ask for confirmation before erasing user EEPROM content.
Key Features
- Trenz 4 x 5 Module socket (3 x Samtec LSHM connectors)
- RJ45 GbE Ethernet
- MicroUSB connector (Device, Host or OTG modes)
- SD Card connector - Zynq SDIO0 bootable SD port
- Pmod connector A, 3.3V
- 6 Pins can be multiplexed to SD Card pins (MIO1 bank when using TE0720)
- 2 Pins connected to carrier controller CPLD
- Pmod connector B, 3.3V
- Mapped to 8 PS MIO0 pins if using TE0720 (same mapping as on zedboard)
- 6 pins also connected to carrier controller CPLD
- Single 12V power supply
- High performance Enpirion DCDC converter for local supplies
- VITA57.1 compliant FMC LPC connector
- Digitally programmable FMC VADJ power supply
- Carrier controller CPLD
- 1200 Macrocell CPLD with Block RAM, Flash and PLL
- 8 user LEDs mappable to different functions
- 2 user pushbuttons mappable to different functions
- VID and EN control for FMC VADJ DCDC regulator
- USB JTAG interface
- Mini USB connector
- Compatible with Xilinx tools: Impact, Chipscope, XMD, Vivado/SDK etc.
- Compatible with OpenOCD debugger including ZYNQ SRST control
- Based on FT2232H USB chip
- Channel A can toggle module (Zynq PS) reset
- Channel B can be used as USB UART
- Carrier controller can reroute RXD/TXD signals
- JTAG port can be connected to (by the carrier controller)
- 4 x 5 module JTAG (FPGA + ARM chained in Zynq)
- 4 x 5 module JTAG and FMC JTAG in chain
- FMC JTAG alone
- Zynq ARM PS JTAG port (via EMIO muxing in TE0720)
- 6 pin header for off board use
- Pmod connector B for off-board use
Scope of Delivery
- 1 x TE0701-06 carrier board for Trenz Electronic modules with 4 x 5 cm standard footprint only
Additional Information
- Manufacturer'sarticle number: TE0701-06
- Trenz Electronic TE0701 Wiki
- Support Forum
All modules produced by Trenz Electronicare developed and manufactured in Germany.
| Technical characteristic | Value |
|---|---|
| Item ID | 102919 |
| Condition | New |
| Legacy item ID | 019685678232713da0aa6f4df96e7583 |
| Model | TE0701-06 |
| Manufacturer | |
| Manufacturing country | Germany |
| Content | 1 piece |
| Weight | 239 g |
| Customs tariff number | 84718000 |
