TE0720-04-61C33MAS Starter Kit (TE0720-04-61C33MAS)

The Trenz Electronic Starter Kit TE0720-04-61C33MAS includesa TE0720-04-61C33MA SoC module on a TE0703-07 carrier board with aheatsink. Supplied with a 5V power supply, two VG96 connectors (DIN 41612), a32 GB microSD card and a USB cable.

The Module: TE0720-04-61C33MA

The Trenz Electronic TE0720-04-61C33MA are SoC modules with commercial temperature range integrating a AMD Zynq Z020 SoC, a Gigabit Ethernet transceiver, 1 GByte DDR3 SDRAM, 8 GByte e.MMC,32 MByte Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/O's is provided via rugged high-speed stacking strips.

Key Features

• AMD Zynq XC7Z020-1CLG484C
• Rugged for high shock and vibration
• ARM dual-core Cortex-A9 MPCore
• 10/100/1000 tri-speed Gigabit Ethernet transceiver (PHY), SGMII accessible on a board-to-board connector
• USB 2.0 high speed ULPI transceiver
• 1GByte (32-bit) DDR3 SDRAM
• 32MByte QSPI Flash memory (for configuration and operation)
• 8GByte e.MMC (optional up to 32GByte)
• Plug-on module with 2 x 100-pin and 1 x 60-pin Razor Beam High-Speed hermaphroditic Terminal/Socket Strips (regular 4 mm)
• 152 FPGA I/O's (75 LVDS pairs possible) and 14 MIO's available on board-to-board connectors
• On-board high-efficiency DC-DC converters
  • 4.0A x 1.0V power rail
  • 3.0 A x 1.5V power rail
  • 3.0 A x 1.8V power rail
• System management and power sequencing
• eFUSE bit-stream encryption
• AES bit-stream encryption
• Valid MAC Address and 2K serial EEPROM
• SHA-256 authentication chip with unique serial number
• RTC, temperature compensated
• 3 user LEDs
• Evenly-spread supply pins for good signal integrity

The Baseboard: TE0703-07

The Trenz Electronic TE0703 carrier board is a baseboard for 4 x 5 SoMs, which exposes the MIO- and the PS/PL-pins of the SoM to accessible connectors and provides a whole range of on-board-components to test and evaluate Trenz Electronic 4 x 5 SoMs.

Key Features

• On Board
  • USB JTAG and UART interface (FTDI FT2232H), compatible withAMD-tools (also with many other tools)
  • SDIO port expander with voltage-level translation
  • 4 x User LEDs
    • D1 and D2 are connected to the carrier controller, their function depends on the firmware
    • D3 and D4 are connected to the 4 x 5 module B2B connector pins, and are directly controlled by the module
  • 1 x User push button
    • Connected to "intelligent Carrier Controller (iCC)" and can be used as module reset button. Other usage possible, actual function depend on the code loaded into iCC
  • 6 A high efficiency power SoC DC-DC step-down converter with integrated inductor for 3.3 V power supply
  • 4 User DIP switches
    • Enable/disable update of the "intelligent Carrier Controller"
    • MIO0 (readable signal by iCC and module)
    • 2 "mode" bits

• Interface
  • Trenz 4 x 5 module socket (3 x Samtec LSHM series connectors)
  • Micro SD card connector - Zynq SDIO0 bootable SD port
  • 2 x VG96 backplane connectors (mounting holes and solder pads)
  • Mini USB connector (USB JTAG and UART interface)
  • RJ45 GbE connector
  • USB-Host connector

• Power
  • Barrel jack for 5V power supply input
• Size
  • 6.45x10 cm

Scope of Delivery TE0720-04-61C33MAS Starter Kit

• 1 x TE0720-04-61C33MA SoC micromodule with AMD Zynq XC7Z020-1CLG484C
• 1 x TE0703-07 carrier board for Trenz Electronic modules with 4 x 5 cm form factor
• 1 x Pre-installed heatsink for TE0720, spring-loaded
• 2 x VG96 connectors (DIN 41612)
• 1 x Power supply 5V with 4000 mA current including four adapter (US, UK, EU, AUS)
• 1 x32 GB Class 4 microSDHC card incl. adapter
• 1 x USB cable, Typ A to Typ B mini, 2 meter length

Additional Information

• Manufacturer's article number: TE0720-04-61C33MAS
• Trenz Electronic Wiki TE0720 Starter Kit
• Support Forum